logo.png

How to Use a Plotter with Scorpion SCAN: 2026 Hyundai Kona Tint Install

Sunday, November 22, 2026

Primary Blog/How to Use a Plotter with Scorpion SCAN: 2026 Hyundai Kona Tint Install
Tint Academy Scorpion SCAN and plotter setup with a Scorpion film box on the cutter, titled Scorpion SCAN + Plotter: Cut, Weed, Shrink, Install

Want to use a plotter with the Scorpion SCAN app, from your phone to a finished rear roll-up install? In this 15-minute walkthrough, Adam from Tint Academy shows the full workflow on a 2026 Hyundai Kona: selecting the vehicle in Scorpion SCAN, sending the pattern to the plotter over a Raspberry Pi, cutting and weeding both rear roll-ups, heat shrinking on the peel board, prepping the glass, and installing the film with a two-stage method, tucked edges, and a bottom load.

Hand cutting still matters. As Adam puts it, you still need to know how to hand cut — it's your primary method. A plotter is the way to go when you want to scale, make the business easier, get better cuts, faster installs, and less waste. The goal is your success.

Watch: How to Use a Plotter with Scorpion SCAN

Watch the full video on YouTube.

Why You Still Need to Know How to Hand Cut

Adam is clear about this from the start: it's really important to hand cut. Hand cutting is your primary method. A plotter does not replace that skill.

If you want to scale your window tint business, though, a plotter makes the work easier. You get better cutting, better and quicker installs, and less waste. In this video, the plotter-cut pattern lined up perfectly on the Kona and saved a lot of time cutting.

Select the 2026 Hyundai Kona in the Scorpion SCAN App

Scorpion SCAN is the app Adam uses to pick the vehicle and send the pattern to the plotter. He describes it as the easiest software to use on the market: a couple of clicks and you have your pattern printed off.

In the video, he selects a 2026 Hyundai Kona, then cuts both rear roll-up windows — the rear driver and the rear passenger.

Scorpion SCAN is about $30 a month, and the first month is free. For film and plotter hardware, visit buyscorpion.com.

Send the Pattern From Your Phone to the Plotter

The pattern goes from the phone to the plotter over a Raspberry Pi, wireless or Wi-Fi. Once the job is sent, the plotter cuts the pattern. In this demo, the cut is underway in about 30 seconds after the send.

Need help getting that wireless link set up? Watch How to Set Up a Window Tint Plotter Wirelessly (A to Z) | Scorpion Scan Software Tutorial.

Weed the Rear Roll-Up Patterns

When the plotter is finished, Adam brings the cut plot over to his peel board. He cuts out the patterns and weeds off the excess film, then cuts through the center to separate the rear driver and rear passenger pieces. After weeding, he has two ready patterns on the board.

Heat Shrink on the Peel Board

Adam shrinks the patterns on the peel board instead of moving the film from the car back to the board. He wants to do the work in one spot. Moving the film around less also means less contamination.

If you don't have a peel board, you can heat shrink on the car.

On the first pattern, he works across the top and down the sides. Because this is a flat surface, he is only on the film for about two to three seconds at a time, then gets one more shrink out of the piece before moving to the rear driver window.

Outside and Inside Prep

Adam is huge on cleaning. He says the number one overlooked aspect of window tinting is the prep. If you have a bad prep, you're going to have a terrible install. Always focus on prep.

Points from the video:

  • Use a white scrub pad.
  • Scrub the window and the entire outside edge, and get everything completely clean.
  • Wipe up the glass and the entire door panel, including the bottom of the door panel, so streaks and overspray don't sit there.
  • When you roll the window down to install, don't get overspray on the glass.
  • A lot of dirt sits on top of the glass, so wet the glass down and spray the air to knock down contamination before the film goes on.

This Kona was a brand new car and still had plastic on it, and he still prepped it carefully. The film in the video is Scorpion film, which Adam says has a very aggressive adhesive — something he really likes. Because of that, he uses a little extra slip solution on the job as well.

Stage 1 of the Two-Stage Install

With the glass prepped, Adam pulls the liner back, slides the pattern in, and gets absolutely perfect alignment. As he puts it, the plotter wins again on this.

Then he does a light squeegee across the top. He doesn't want a hard squeegee that could shift the film. After another spray, he pushes as hard as he can side to side to remove as much slip solution as possible. He takes a spatula down each side, locks both sides, and slowly pushes the window up. Stage one is done.

Tucking the Edges

This is where a lot of tinters go wrong and start creasing the sides. Adam moves in close to show the tuck: the film drops in, gets anchored, and he repeats the same thing on the other side, working up, across, and down so the edges sit cleanly.

Bottom Load

For the remaining piece, Adam bottom loads the film. The seal is already removed. He sprays the entire area, peels the liner back, sprays the film, drops it onto the glass, and lines up the side. The alignment is perfect, with the entire piece of film on the glass.

He does a light squeegee across the top, works out to the sides, then pushes everything out. When he rolls the window up, the entire piece of film is already on the glass, so he just comes through and pushes everything straight down.

That's the bottom load — very easy to do when the pattern lines up. In this install, it lined up perfectly and saved a lot of time cutting.

Scorpion SCAN and Plotter Starter Packages

If you're looking at scaling in window tinting — better cuts, faster installs, and less waste — Adam's advice is to jump on a plotter now, while still knowing how to hand cut.

Scorpion has bundles behind the plotter in the video. Click through and you can get a full plotter, a full Raspberry Pi, and four rolls of film for a great entry price. See the Tint Academy New Dealer Starter Packages (Scorpion SCAN and plotter bundles) on BuyScorpion, or browse buyscorpion.com.

Scorpion SCAN is about $30 a month after a free first month.

Learn Window Tint and Watch Related Videos

Adam also points to a full list of videos that break down shrinking, outside prep, and installation. If you want to see something else, contact Tint Academy below and they'll film it. The goal is your success.

Watch next:

For hands-on window tint training, visit tint.academy.

Call or text USA 321-364-9518 or Canada 289-201-2070.

Scorpion SCAN Plotter FAQ

Do I still need to know how to hand cut if I use a plotter?

Yes. Adam says it's really important to hand cut, and that hand cutting is your primary method. A plotter helps you scale, get better cuts, faster installs, and less waste, but you still need to know how to hand cut.

How much does the Scorpion SCAN app cost?

In the video, Adam says Scorpion SCAN is about $30 a month, and the first month is free. He also calls it the easiest software to use on the market: a couple of clicks and you have your pattern printed off.

How do you send a pattern from your phone to the plotter?

Select the vehicle in the Scorpion SCAN app — in this video, a 2026 Hyundai Kona — then send the pattern to the plotter over a Raspberry Pi, wireless or Wi-Fi. The plotter cuts the pattern, and you weed it on the peel board.

Can you heat shrink on the car if you don't have a peel board?

Yes. Adam shrinks on the peel board so he can keep the work in one spot and move the film less, which means less contamination. If you don't have a peel board, he says you can do this on the car.

Why is prep so important before a window tint install?

Adam says the number one overlooked aspect of window tinting is the prep. If you have a bad prep, you're going to have a terrible install. Use a white scrub pad, clean the glass and the door panel, knock down contamination, and don't get overspray on the glass when you roll the window down.

Where can I get a Scorpion SCAN and plotter bundle?

See the Tint Academy New Dealer Starter Packages on BuyScorpion. Adam says the bundles can include a full plotter, a full Raspberry Pi, and four rolls of film for a great entry price. For training, visit tint.academy, or call or text USA 321-364-9518 or Canada 289-201-2070.

customer1 png

Hi, I Am Jane Doe

CEO Of Best Blog Ever

Lorem ipsum dolor sit amet, consectetur adipisicing elit. Autem dolore, alias,numquam enim ab voluptate id quam harum ducimus cupiditate similique quisquam et deserunt,recusandae.

1 png

Get Our Best Selling Product!

You just read about this...

Super excited about this product? We are, too! We just wrote this whole blog post that mentions it.

Ready to buy it? Get access to the Product here: